OWNER S MANUAL6.1 ChannelHome Theatre Receiver
Connection09Connect the component with RCA to RCA cords. Make sureto connect :white plug to white jack(L:left)red plug to red jack(R:right)If the CD p
Connection10Connecting the supplied antennasConnecting the supplied FM antennaThe supplied FM antenna is for indoor use only.During use, extend the an
Connection11Positioning of the SpeakersThe positioning of speakers differs according to the sizeand acoustics of the listening room. While actuallylis
Remote Control Unit12By using the provided remote control unit, the receiver canbe controlled from your listening position.To use the remote control u
Basic Operations13BALANCE ControlThis control is used to adjust the balance of the frontspeakers.Normally set to the center position.EBASS BOOST Switc
Basic Operations14Basic Operations (3)PHONES jackFor private listening, insert optional (not included)headphones (1/4-inch plug) into the PHONES jack,
Radio Reception15Select the TUNER mode by turning the FUNCTION selector.1Select the station you want to listen to (auto selection).4Hold down the TUNI
Radio Reception16Radio Reception (3)Select the TUNER mode by turning the FUNCTION selector.1Press the MEMORY button for more than 1.5 second.Up to 30
RDS OPERATION17RDS OperationNow in use in many countries, RDS (Radio Data System) is adescription of the station's programming hidden space in th
Video Operations18Select the VCR/VID 1, TV/VID 2, AUX/VID 3 or DVD/CD modeby turning the FUNCTION selector.Play the component corresponding to the FUN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to thepresence of uninsulated dangerous volta
Available Surround Modes19The surround functions create a live atmosphere such asthat experienced in movie theaters, stadiums and concert halls.Select
Available Surround Modes20Surround mode changes as follows whenever you pressthis button.Dolby Digital EXIn a movie theater, film soundtracks that hav
Available Surround Modes21Dolby Pro Logic II brings the excitement of surround sound to anystereo mix, while making existing Dolby Surround mixes soun
Speaker Configuration22Each press of the SPEAKER CONFIGURATIONbutton will change the desired Speaker Configurationshown on the display. (ex.: FNT-LARG
Delay Time23Delay TimeThe delay time can be individually set for the DolbyDigital/ Dolby Pro LogicII modes using the DELAY TI ME(CENTER/REAR) buttons.
Test Tone24Press the TEST TONE button in DTS, Dolby Digital orSurround mode.The test tone is emitted fromeach speakerin the followingorder at 2-second
TROUBLESHOOTING25Problem Probable Cause RemedyAmplifierTo determine any problem with your receiver, always check the most obvious possible causes firs
Specifications26Amplifier SectionOutput PowerStereo Mode : 120W/CH(1% THD 1KHz 8ohm DIN)Surround Mode : 92W/CH(1% THD 1KHz 8ohm DIN)THD : 0.01%DOLBY D
IMPORTANT SAFETY INSTRUCTIONS02FOREWORDThis section must be read before any connection ismade to the mains supply.EQUI PMENT MAI NS WORKI NG SETTI NGY
Contents03Before Use...4Description ...
Before Use04Speaker ConnectionsCaution:To avoid damaging the speakers with a sudden high-levelsignal, be sure to switch the power off before connectin
DESCRIPTION05DTS was introduced in 1994 to provide 5.1 channels ofdiscrete digital audio into home theater systems.DTS brings you premium quality disc
Connection06Power cord (AC)Be sure to connect the power cord to an AC outletwhich supplies the correct voltage.Hold the power plug when plugging or un
Connection07OUT6CH OUTDVDSR SL CSWEQIN6 CHANNEL INPUTBy connectiong a DVD Audio player, SACD multichannel player, or other component that has a multic
Connection08If the video component is equipped with S-VIDEO jacks,it is recommended that it be connected to the AVR-800or directly to the television m
Kommentare zu diesen Handbüchern